Log in or sign up


USER:
PASS:

 
 
Products
Post Tensioning System Accessories


150 KSI All-Thread-Bar
R71 150 KSI All-Thread-Bar - ASTM A722

R71 150 KSI All-Thread-Bar - ASTM A722

Nominal Bar DiameterMinimum Net Area
Thru Threads
Minimum Ultimate StrengthMinimum Yield StrengthNominal WeightApprox. Thread
Major Dia.
Part Number
1" (25 mm)0.85 in2 (549 mm2)128 kips (567 kN)102 kips (454 kN)3.09 lbs./ft. (4.6 Kg/M)1-1/8" (28.6 mm)R71-08
1-1/4" (32 mm)1.25 in2 (807 mm2)188 kips (834 kN)150 kips (667 kN)4.51 lbs./ft. (6.71 Kg/M)1-7/16" (36.5 mm)R71-10
1-3/8" (36 mm)1.58 in2 (1019 mm2)237 kips (1054 kN)190 kips (843 kN)5.71 lbs./ft. (8.50 Kg/M)1-9/16" (39.7 mm)R71-11
1-3/4" (45 mm)2.60 in2 (1664 mm2)400 kips (1779 kN)320 kips (1423 kN)9.06 lbs./ft. (13.5 Kg/M)2" (50.8 mm)R71-14
2-1/2" (65 mm)5.19 in2 (3350 mm2)778 kips (3457 kN)622 kips (2766 kN)18.20 lbs./ft. (27.1 Kg/M)2-3/4" (69.9 mm)R71-20
** 3" (75 mm)6.46 in2 (4169 mm2)969 kips (4311 kN)775 kips (3448 kN)22.3 lbs./ft. (32.7 Kg/M)3-3/64" (78.2 mm)R71-24
** The 3" diameter bar is not covered under ASTM A722.


BEM-TYPE A
BEM-TYPE B
1.Bearing Plate4.Duct
2.Spiral Reinforcement5.Wedge
3.Trumpet Duct6.Anchor Head

  • Dimensions in mm
  • "N"=the number of spiral reinforcement.
  • □c can be provided as □k of BEM TYPE B
  • Subject to modification.

R73 Hex Nuts - ASTM A29

Hex Nuts
Nominal Bar
Diameter
Across FlatsAcross CornersThicknessPart Number
1" (25 mm)1-3/4" (45 mm)2.02" (51.3 mm)2" (51 mm)R73-08
1-1/4"(32 mm)2-1/4" (57 mm)2.60" (66.0 mm)2-1/2" (64 mm)R73-10
1-3/8" (36 mm)2-1/2" (64 mm)2.89" (73.4 mm)2-3/4" (70 mm)R73-11
1-3/4" (45 mm)3" (76 mm)3.46" (87.9 mm)3-1/2" (89 mm)R73-14
2-1/2" (65 mm)4-1/4" (108 mm)4.91" (125 mm)4-3/4" (120 mm)R73-20
*3" (75 mm)4-1/4" (108 mm)5" (127 mm)6-1/8" (156 mm)R74-24
*Round nut with outside diameter of 5" (127 mm)

Coupler ASTM A29, C1045

Coupler, with which two strands are joined thus enabling remaining strand/wire pieces to be used up

R73-JN Jam Nuts - ASTM A29, C1045

These Jam Nuts can't be substituted for full strength nuts anc can't be used on bars other than NOOR 150 KSI All-Thread-Bars of the same diameter.

Jam Nuts
Nominal Bar
Diameter
Across FlatsOverall LenghtPart Number
1" (25 mm)1-3/4" (45 mm)1/2" (12.7 mm)R73-08JN
1-1/4"(32 mm)2-1/4" (57 mm)5/8" (15.9 mm)R73-10JN
1-3/8" (36 mm)2-1/2" (64 mm)11/16" (17.5 mm)R73-11JN
1-3/4" (45 mm)3" (76 mm)7/8" (22.2 mm)R73-14JN
2-1/2" (65 mm)4" (108 mm)1-3/16" (30.2 mm)R73-20JN
*3" (75 mm)4-1/4" (108 mm)2" (51 mm)R74-24JN
*Round nut with outside diameter of 5" (127 mm)

Steel Bearing Plates

S1K - RoundS1K - KeyholeR80 - DishedS1K - StuddedS1K - Domed
NOOR steel bearing plates are standard with a round hole for non-grouted anchors. Also available are dished plates for use with spherical hex nuts and keyhole plates which provide free access for grout tube entry. Bearing plates are customized for each application. Plate dimensions should be specified around the parameters of the project. In addition, corrosion protection should be considered along with specifying hole diameter and bar angle. Stainless steel plates available upon request.

End Caps

NOOR offers end caps produced from fiber reinforced nylon, steel or PVC to provide corrosion protection at otherwise exposed anchor ends. Most often the caps are packed with corrosion inhibiting wax or grease. Caps made from reinforced nylon and steel are used in exposed impact areas. The fiber reinforced nylon end cap meets the Florida DOT standards.

Fiber
Reinforced
Nylon Cap
Slip-On PVC Cap
with Plastic Nut
Screw-On PVC CapSteel Tube
with Jam Nut
Steel Tube Welded
on Flange with Threaded
Screw Connections
Dead End


Life End Anchorage System

Flat anchorage Post-tensioning System
NOOR is a flat-anchorage post-tensioning system using 1 to 5 seven-wire prestressing strands. The prestressing strands have a nominal diameter / nominal cross section of 12.7 mm / 100 mm2, 15.3 mm / 140mm2 or 15.7 mm / 150mm2 and a maximum characteristic tensile strength of 1960 MPa.
The available anchorages are the stressing or active anchorages (Type A), the fixed or passive anchorages (Type F) and fixed as well as movable couplers (Type K). The tendon sheaths are corrugated steel ducts or PT plastic ducts, which are injected with a high performance grout.
The life end anchorage system is normally adopted for bonded tendon. The strands are individually gripped in one slab anchor head unit and transmit their prestressing forces by means of slab type anchor plate casting unit. The strands are stressed individually by means of a mono strand jack. The strands are contained in one flat duct which is made of corrugated galvanized or non-galvanized metal. To ensure corrosion protection and to give adequate bond strength, the tendons are filled with suitable cement grout mix after complete stressing of the strand




TYPEABCDEFGR
SA5-410.423.78.59.751.751.966.754.33
SA5-510.423.78.59.751.751.968.754.33
SA6-410.423.78.59.752.242.647.514.33

Wedge

A wedge assembly typically has 2 or 3 part wedges with a spring wire retainer clip in a groove around the thick end. It is placed around a strand to grip and secure it by wedge action in a tapered hole through a barrel. Available in two nominal sizes, 12.7mm (0.5in) and 15.2mm (0.6in) diameter


Each individual wedge segment is examined for exact tooth shape bycomputer cameras.
Anchor barrels are manufactured from hightensile crack-tested basic material in a special process, and are only stamped and released for dispatch after final ultrasonic testing.
In this way, we ensure the highest industrial safety and long service life of the anchor components

Local Zone Reinforcing

The compressive strength of the concrete in the local zone (area directly under the bearing plate) can be enhanced when necessary by use of lateral confinement of spiral reinforcement. The rebar spirals are available in #3 through #5 diameters of Grade 60 Rebar and made to the project design requirements for diameter, pitch, and length. They are also available with or without a deformation pattern.

R82 Galvanized Metal Corrugated Duct - ASTM A653

NOOR Galvanized Spiral Metal Duct or High Density Polyethylene Duct meets all physical and structural recommendations for post tensioning duct as laid down by the Post Tensioning Institute (of the United States). The Duct is available in 2”, 3”, and 4” diameter with couplings and reducer couplings for all sizes.

R75 Polypropylene & Polyethylene Corrugated Duct

The stable characteristics of NOOR polypropylene & polyethylene duct are normally preferred where additional corrosion protection is desirable. Polypropylene Duct has been approved by the Florida DOT for internal tendons and is available in 2-3/8” diameter. Polyethylene Duct is available in 2”, 3”, and 4” diameter. Couplings and reducer couplings are available for all sizes.
TypeTendon unithHbBS
Plastic duct PT-PLUS5-2,6-20.751.181.652.090.08
Plastic duct PT-PLUS5-4,6-40.831.382.833.390.08
Steel duct 5-4,6-40.710.832.832.950.01


NOOR-G Expansive agent for the production of shrinkage-compensating and high strength concrete

Product Description

NOOR-G is an inorganic product in powder form to be used in addition to the other components of concrete for producing shrinkage compensating and high strength concrete. It is a special clinker, burnt at high temperature, rich in free lime and whose minor compounds are calcium silicates, aluminates, Ferro-aluminates and sulphates. The use of super plasticizers is particularly recommended when using NOOR - G as they significantly reduce the water content and thus the potential shrinkage of the concrete to be compensated.


click here to download technical data sheet (TDS) of the product

click here to download material safety data sheet (MSDS) of the product
Compressive Strength (70° F Dry Environment) 0.4 w/c Ratio

TimePSIMPa
1 Day1,80012.4
3 Days4,00027.5
7 Days6,00041.4


T3P Heavy Duty Plastic Grout Tube

Furnished in product lengths for the anchors or in rolls.
O.D.I.D.Part No.
3/8" (9.5 mm)1/4" (6.4 mm)T3P03002
1/2" (12.7 mm)3/8" (9.5 mm)T3P04003
5/8" (15.9 mm)1/2" (12.7 mm)T3P05004
3/4" (19.1 mm)5/8" (15.9 mm)T3906005
1" Nom. (25.4 mm)3/4" Nom (19.1 mm)T3P06
Super Plasticizer

Plasticizer is available and is used as a water reducer for ease of pumping grout through tubes at lower water to cement ratios.

Bar Chairs



NOOR provides the strongest Bar Chairs available in the market. They are made from fiber-filled composite material and exceed the strength of comparable wire supports by up to ten times. The product size is identified on the top of the product and on the foot. WE composite material offers continuous corrosion protection, both on the job-site and in concrete providing a great alternative to epoxy, stainless, and galvanized bar supports.
The line of Composite Bar Chairs contains points on the bottom of the feet that firmly hold the chair in place and feet that can be stapled to the deck when necessary. Composite Bar Chairs are grey in color (custom colors are available) to blend in with concrete and show virtually no change in strength in temperatures ranging from 0ºF to 300ºF.

Primary Uses:
  • Single Mat Support – Post-Tensioning, Rebar, or Mesh
  • Bottom Layer Double Mat Support – Post-Tensioning, Rebar, or Mesh
  • Tilt-Up Concrete Wall Panels
  • Slab-on-Ground using a Sand Plate


UN bonded mono strand system
consists of a seven-wire strand coated with corrosion inhibiting grease and encased in polyethylene sheathing according to ASTM416 and fabricated in compliance with PTI.Both non-encapsulated and encapsulated anchors recommended for corrosive environments are available





Type156789Kg
0.5"/0.52"6.53324.5413813100127570.61
0.6"/0.62"8.54026.8484214105133600.88


  • Dimensions in mm
  • Used with BEW13 wedge 25.4Φ×35L, BEW15 wedge 27.7Φ×41L













Copyright © 2001 - NOOR Company. All rights reserved.
Main office At Manhattan 1133 Broadway, Suite 706
New York, NY 10010 – USA
Tel 001.212.631.5819 Fax 001.212.631.5820